Krohne TIDALFLUX IFM 4110 PF EN User Manual

7.30830.32.00 Installation andoperatinginstructionsTIDALFLUXIFM 4110 PFElectromagneti

7.30830.32.00108 Outer sheathBootstrap signal cable type BTSThe signal converter automatically controls the individual shields (3) to exactly the sam

7.30830.32.0011C1203023121110 871 2 3IFC110 PF IFS4000 PFPE N L N L PEInterfaceElectrodesCoilsPowerA B C D E8 778NC NC DNCC121011 ENCNC230/1

7.30830.32.00122. Installation of the signal converter2.1 Please note the following information concerning installation and operation of the IFC 110 P

7.30830.32.0013• Active mode: the signal converter supplies the power for the operation (selection) of receiver instruments,observe max. operating da

7.30830.32.00142.5.3.2 Pulse output A1 for electromechanical totalizersPLEASE NOTE:The output terminal A1 can be used as status output A1 or as a 2nd

7.30830.32.0015• Connection diagrams see sect. 2.5.6.• Schematic wiring diagram for status outputs A1/A2 and D1/D2.These status outputs have MOSFET

7.30830.32.0016PPD1D⊥D2C1C⊥C2I+I-A1A⊥A2E+E-I IContacts 24 V, 10 mAI ≤ 7 mAControl inputsC1 / C2 activePPD1D⊥D2C1C⊥C2I+I-A1A⊥A2E+E-I I _∼∼UextUext ≤ 32

7.30830.32.0017reverseflowforwardflowElectronic totalizers must be connected as shown in the connection diagrams for pulse output Pon the following fi

7.30830.32.0018* Shielded cables must be used to prevent radio interference at pulse output frequencies > 100 Hz.for frequencies ≤ 1 kHzUext. ≤ 3

7.30830.32.00192.5.7 Standard factory settingsAll operating data are set at the factory in accordance with the specifications contained in the order.

7.30830.32.002ContentsProduct liability and warrantySystem descriptionAvailable versionItems included with supplyCE / EMC / Standards / Certificationp

7.30830.32.00203 Start-up• Before connecting to power, check that the instrument is correctly installed as described in Sections 1 and 2.• The flow

7.30830.32.0021Part B Signal converter IFC 110 PF4. Operating the signal converter4.1 Krohne operating conceptMeasuring modeWhen this is shown on the

7.30830.32.00224.2 Operating and control elements…the 15 keys à and Ä accessibleafter removal of the glass cover,…the 3 magnetic sensors Ç and the

7.30830.32.00234.3 Key functionsIn the following, the cursor or flashing part of the display is shown against a gray background.To start operator con

7.30830.32.0024Shift to leftTo alter text (units)In case of units, the numericalvalue is converted automatically.Select next textSelect preceding text

7.30830.32.0025Fct. No. Text Description and setting1.0 OPERATION Operating menuFULL SCALE Full-scale range for flow rate Q100%Selection of unit• m3/h

7.30830.32.0026Press ↵ key to change to subfunction “RANGE I”→ RANGE I Selecting the measuring range• 0-20 mA • 4-20 mA (fixed ranges)• mA (user-defin

7.30830.32.0027→ • OFF • ON • ALL ERROR • FATAL.ERROR• INVERS D1 (inverse mode of D1 and D2)• INVERS A1 (inverse mode of A1 or A2 possible only if A1

7.30830.32.0028Fct. Text Description and settings3.0 INSTALL. Installation menu3.01 LANGUAGE Select language for display texts• GB / USA (English) • F

7.30830.32.0029→ ADC GAIN Set gain of A/D converter• AUTO • 10 • 30 • 100 Select with ↑ or ↓ keyPress ↵ key to change to subfunction “SPEC. FILT.”.→ S

7.30830.32.0035.3 Low-flow cutoff SMU5.4 Display5.5 Internal electronic counter5.6 Internal power supply (E+ / E-) for connected loads5.7 Curren

7.30830.32.0030ADC-HARDW. Hardware error A/D converter Replace ADC printed circuit boardADC GAIN Hardware error A/D converter Replace ADC printed circ

7.30830.32.00315. Description of functions5.1 Full-scale range Q100%Fct. 1.01 FULL SCALEPress → keySelect unit for full-scale range Q100%•• m3/hr (cub

7.30830.32.00325.3 Low-flow cutoff SMUFct. 1.03 L.F. CUTOFFPress → keySelect• OFF (fixed tripping points: ON = 0.1 % / OFF = 0.2 %)• PERCENT (variabl

7.30830.32.0033Setting of totalizer format• Auto (exponent notation)• # . # # # # # # # • # # # # # . # # #• # # . # # # # # # • # # # # # # . # #• #

7.30830.32.00345.6 Internal power supply (E+ / E-) for connected loadsPassive loads connected to the outputs and inputs can be fed by means of the int

7.30830.32.0035→→ I ERROR = set error value, press → key• 22 mA fixed value• 0.0 – I0% mA variable value, only variable when I0% ≥ 1 mA, see “RANGE I”

7.30830.32.0036→→ PULSWIDTH = select pulse width, press → key• AUTO automatic = 50 % of cycle duration of 100 % output frequency• SYM. symmetric = pu

7.30830.32.00375.9 Status outputs A1 / A2 and D1 / D2PLEASE NOTE:Connection diagrams see sect. 2.5.6.Status outputs A1 A2 D1 D2Select Fct. _ . _ _the

7.30830.32.0038•• Characteristic of status outputs Switch open Switch closedOFF (switched off)no functionON (e.g. operation indicator)power supply OFF

7.30830.32.0039Select with ↑ and ↓ keys.Press ↵ key to return to Fct. 3.01 LANGUAGE.5.12 Entry codeFct. 3.04 ENTRY CODEPress → keySelect• NO no code,

7.30830.32.00410.2.1 General information10.2.2 Dimensions and weight IFC 110 PF10.3 Complete system IFM 4110 PF10.3.1 Full-scale range Q100%10.3.2

7.30830.32.0040→→ LINE FREQ. = set power frequency customary in country where instrument is used, press → key(Please note: only applies to instruments

7.30830.32.0041Factors for volume FMVolumetric unit TEXT VOL. Factor FMSettingCubic metersm31.01.00000 E+0LiterLiter10001.00000 E+3Hectolitersh Lit101

7.30830.32.00425.16 Output characteristicsI current outputI0%0 or 4 mAI100%20 mAP pulse outputs P and A1 (P2)P100%pulses at Q100%, full-scale rangeQF

7.30830.32.00435.17 ApplicationsFct. 3.06 APPLICAT.Press → key twiceSet flow characteristics, select with ↑ or ↓ keys• STEADY steady flow• PULSATING

7.30830.32.00445.19 Limit switchesFct. 1.07 – 1.10 Status outputs A1, A2, D1 and D2(Define operating mode of output terminals A1, see sect. 5.18)Pres

7.30830.32.0045Press ↵ key to return to Fct. 1.07 – 1.10, status outputs A1, A2, D1 or D2.External range change by control inputFct. 1.11 or 1.12 Cont

7.30830.32.0046Part C Special Applications, Functional Checks,Service and Order Numbers6. Special applications6.1 Use in hazardous areasThe IFS 4000 P

7.30830.32.0047Resetting the signal converter, see sections 4 and 5.When changing the signal converter settings, the green LED (normal) and the red LE

7.30830.32.0048Set subfunction “LIMIT CNT.” to 10 on a trial basis.Should the measuring value leave the above window in one direction more than 10 ti

7.30830.32.00497. Functional checks7.1 Checking the zero with IFC 110 PF signal converter, Fct. 3.03• Set “zero” flow in the pipeline. Make sure that

7.30830.32.005How to use these Installation and Operating Instructions• For easy reference these instructions are divided into 5parts.• Only Part A

7.30830.32.0050 allow your flowmeter to be subjected to a simple and rapid diagnosis.• Press the following keys for a display of the status codes:Ke

7.30830.32.00517.4 Hardware test, Fct. 2.03Please note:Before beginning the test, deactivate any alarms and controllers as the current output will be

7.30830.32.0052LED 2Red LED flashes Fatal error, hardware and/orsoftware faultReplace signal converter, seesect. 8.3LED 3Cyclic flashing of red LED,ap

7.30830.32.0053Group I Faults / Symptoms Cause Remedial actionDisplay shows…I SHORTCurrent output shorted,load < 15 ΩEliminate short circuit,load m

7.30830.32.0054Group P Faults / Symptoms Cause Remedial actionWrong connection / polarity Connect properly, see sect.2.5.3 and 2.5.6, noterecommended

7.30830.32.0055Group S Faults / Symptoms Cause Remedial actionDefective signaling instrument(s)or external voltage sourceCheck signaling instrument(s)

7.30830.32.00567.6 Checking the primary headSince the primary head consists of two “separated” parts (velocity measurement and level measurement), the

7.30830.32.0057electrodes contaminated.4When signal line BTS (bootstrap) isused:measure resistance between thefollowing lines:1 and 20 / 1 and 30 / 20

7.30830.32.0058Switch off the power supply before starting work.1) Remove the cover from the terminal compartment of the signal converter.2) Disconn

7.30830.32.00594.2) Determine position of switch Y: use table (GS 8 A front panel) to determine value Y which comes closest to factor X andmeets condi

7.30830.32.006Available versionSystem: IFM 4110 PFPrimary head:• type: IFS 4000 PF• liner measuring section: Irathane• Meter size: 200 - 600 mm /

7.30830.32.00604.3) Calculate setpoint reading “I” for current output: I = I0% + YX (I100% - I0%) in mAI0%current (0/4 mA) at 0% flow rateI100%current

7.30830.32.0061If you need to return your flowmeter to Krohne, please refer to the last-but-one page of these instructions.

7.30830.32.00628. Service8.1 Replacing the power supply fusePower supply fuse in IFC 110 PF signal converterSwitch off the power supply before openi

7.30830.32.00638.3 Replacing the complete electronic unit of the IFC 110 PF signal converterSwitch off the power supply before opening the housing.1)

7.30830.32.00648.4 Replacing single printed circuit boards (PCBs)Switch off the power supply before opening the housing.1) Remove the cover from the

7.30830.32.0065Jumper X4DC operation ≤ 0.2 AAC operation ≤ 0.1 A(factory setting)X1 plug-in terminals inside terminal compartmentX2 internal connectio

7.30830.32.0066Analog/digital converter PCB, ADCX1 internal connection to motherboard IC 12 microprocessorX2 plug-in terminals in terminal compartment

7.30830.32.00679 Order numbersSpare parts Order No.Electronic unit with display 100-230 V AC without magnetic sensors 2106680000100-230 V AC with magn

7.30830.32.0068Part D Technical Data, Measuring Principle and Block Diagram10. Technical data10.1 Primary head IFS 4000 PF10.1.1 General informationM

7.30830.32.006910.1.2 Dimensions and weight IFS 4000 PFMeter size to … Dimensions in mm (inches)DIN 2501Approx.weightMmPNANSIB16.5a b ∅c D j ∅D ∅Di kg

7.30830.32.007Part A System installation and start-up1 Installation of the primary head1.1 Selecting the installation location1. Location and positi

7.30830.32.0070Pulse outputs (passive) P A1(also used as status output)- for electronic totalizers - for electromechanical totalizers- all operating d

7.30830.32.0071Local display 3-line LCDDisplay function current flow, forward, reverse and sum totalizers (7-digit) or 25-digit bar graph withpercenta

7.30830.32.007210.2.2 Dimension and weight IFC 110 PFWeight approx. 4.1 kg (9.0 lb)Dimensions in mm (inch)10.3 Complete system IFM 4110 PF10.3.1 Full

7.30830.32.0073Flow tablev = flow velocity in m/s v = flow velocity in ft/sMeter size Full-scale range in m3/hr Meter size Full-scale range in US Gal/

7.30830.32.007411 Block diagramAD µµPEEPROM 1 EEPROM 2EEPROM-EEPROM µµP• LC display• 15 keys• 3 magnetic sensors (optional)KSA 04 µµPEEPROMP

7.30830.32.0075ÀÀ ADC printed circuit board, analog/digital converter (terminals 1, 2, 3, 20 and 30)• Signal processor protected against overload, f

7.30830.32.007612 Measuring principleThe TIDALFLUX IFM 4110 PF is an electromagnetic flowmeter with an integrated capacitive level measurement system,

7.30830.32.0077Part E IndexKeyword Sect. No. Fct. No. Keyword Sect. No. Fct. No.AA1 status or 2nd pulse outputA1/A2 status outputsAbbreviationsADC see

7.30830.32.0078Electrical connection- GS 8 A simulator- inputs- outputs- power supply- primary headElectromagnetic compatibility- setting- contro

7.30830.32.0079PP = pulse outputsPCB = printed circuit boardPC softwarePE = protective conductorPower supply- connection- failure- frequency- inpu

7.30830.32.008350 10 16x M20 75 (54.2)400 10 16x M24 104 (75.2)500 10 20x M24 107 (77.4)600 10 20x M27 138 (99.8)MetersizeinchesBodypressureratingpsig

7.30830.32.0080If you need to return flowmeters for testing or repairing to KrohneYour electromagnetic flowmeter has been carefullymanufactured and te

7.30830.32.0091.5 Electrical connections of primary head1.5.1 Connection to powerElectrical connection in conformity with VDE 0100 / EN 61010-1“Regu